TIPS ABOUT HOW TO Extend Smok Pen Recharge Time


TIPS ABOUT HOW TO Extend Smok Pen Recharge Time

The Smok Pen is a new pen that was created by two guys in California. They wished to create a cool writing instrument that appeared as if a genuine pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the market by storm.

smok pen

The Smok Pen includes a built quality that’s just great. I came across that even though it can be an electronic pen the construction is simply as good as any of the pens that I’ve reviewed. It is because of how they made the most notable cap. You don’t have to worry about the cap cracking or breaking you Smok Valve Pen.

The two biggest differences that separate the Smok Valve from other pens is the form of the coils and just how that they are built. Generally the coil on a Smok Pen is larger than on other pens. I believe that they did this deliberately, to help make the pen feel bigger.

If you take a look at a Smok Pen, you will observe that the body of the pen is round and not smooth like other pens. On the back of the pen there is a little tab that houses the coil. Once you press on the tab it is simple to turn the heating element on and off. I really liked this feature because it allows me to use the Smok Pen 22 whenever I feel like smoking.

To use the Smok Pen you have to keep the heat button pressed. After the button is pressed, the heating element will begin to warm up. Once it reaches the appropriate temperature it is possible to turn off the heating element. Smok recommends utilizing a 22mm tank. I prefer a larger tank, but that’s just me.

Once you put your Smok Pen in to the tank you will see a indicator light come on. The indicator light will stay green unless you put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is very important always put your pen into the charger before you apply the e-liquids to the coil heads. It is also important to do this before putting your e-liquids in to the coil heads.

After you have completed this step, you should always check to see if you are at the right temperature for the coils to fire. Or even then you should turn the power off and try again. Should you be still not satisfied together with your Smok Pen i quickly suggest you take it in for some troubleshooting. This is what I’d call the “troubleshooting process” because sometimes things just usually do not work as they should. I suggest that you perform the next two steps, then go ahead and check the Smok Pen to see if it still has the electronic charging port.

Before you go any further you should remove the battery from your own pen and unscrew the magnetic cap. You need to then remove the plastic sleeve that holds the sub-ohm. There exists a wire that runs through the Smok’s body that is green in color. You need to loosen this wire using pliers. When you have loosened this wire after that you can access the sub-ohm. You should then remove the wire from the Smok’s body and carefully insert it in to the Smok pen’s electrical port, being careful never to touch any of the coils.

When you have placed the sub-ohm tank into the pen you need to then place all of those other components like the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Start the energy and follow the on screen instructions. You should place the pen’s battery in to the microwave and activate the setting. You should then wait approximately 30 seconds before turning it back off. When you initially put the pen in to the microwave the electronic reading will show a low voltage protection setting. If this setting does not automatically get set you then should follow the on screen instructions.

After the Smok Pen has reached the temperature that it needs to reach you need to then connect both wires to the negative and positive on the positive post on the Smok unit. You should then connect another end podsmall of the battery to the negative post on the negative side of the Smok unit. The ultimate step is to connect the positive cable to the bottom of the Smok’s power switch.

After all the components have been placed into the pen, you should turn the energy on. Following the first test run, you need to be able to see the battery life indicator light come on. If you do not see any sign of life from the Smok Pen, you should take away the battery from the pen and replace it with a fresh one. For your convenience gleam green light which can be pressed in order to confirm the battery charging status. When you have done these things and you also do not start to see the green light indicating charging, you should replace the battery.